Step 4 Tail lights. Información Prensa Derechos de autor Creadores Publicidad Desarrolladores +YouTube Términos Privacidad Política y seguridad Enviar sugerencias ¡Prueba algo nuevo! There is meant to be a clip or something you have to … I have a JM Star 150cc (Tank Clone) I am trying to find out what is the purpose Ideas? this contact form
Same exact result as the previous bulb. To test it, start up the bike, put a volt meter on it. dont order one untill you are sure its the stator mate, and it might be just a damadged wire, Or maybe the Grounding from the Engine to Subframe and than the All the other lights do, like brake, indicators, front lights.
If this is not adjusted correctly, your scooter may not run, or run very poorly. Mopeds don't have keys, they have kill switches. Mostrar más Cargando...
Lol! This screw controls the idle speed, the tip should extend about an 1/8 of an inch (4 mm). Siguiente Turn Signal / Headlight Switch Disassembly & Cleaning Procedure Part 1 - 07+ Suzuki Burgman 400 - Duración: 5:10. Chinese Scooter Headlight Not Working The yellow wire (brown on Indian loom) coming out of the mag flange comes directly from the lighting coils.
The following outline describes the most common symptoms. Scooter Lights Not Working This is most always set at 1 full turn out. If the switch proves to be bad, however, I plan to run a new wire from some point that's hot with the engine on to the tail light. Headlights and tail lights have worked in the past.
I'll need to put the bike back together, or get some fuel into it. 150cc Scooter Headlights Not Working Much like on a car where the horn is on the brake light system so you can test your horn to see if the fuse to the brake lights is working, If you can't find what you want here, feel free to explore the other archived topics listed here. Keep Up to Date Help Us Grow Review your scoot!
all lower case?
We could wire the dash and tail light right to the ignition switch. Scooter Headlights Not Working The spark plug must be clean, and must be replaced promptly when signs of wear begin to show. Scooter Tail Light Not Working Then keeping all the wires plugged in check for a feed from each of the wires other than the two greens. (Working) If the bulb lights up with the bike ticking
or does it ground through the body of the light? weblink I am no electrician but here are the things I checked: 1. tvnacman PM tvnacman tvnacman's Posts tvnacman's Threads Doc's Anything Goes Currently Offline Posts: 2,632 Likes: 60 Joined: Oct 23, 2010 19:29:21 GMT -6 Running Lights not workin by: tvnacman - Jun also battery gets no voltage change. ... 150cc Scooter Headlight Troubleshooting
Any ideas of what I'm looking for? But, the headlight is always on, so this switch could only control the running lights. I believe the bike is wired so the headlight is always on. navigate here Idioma: Español Ubicación del contenido: España Modo restringido: No Historial Ayuda Cargando...
Allow the filter to dry before re-installing it into your gas scooter. 150cc Scooter Lights Not Working Police And Donuts 2.445.158 visualizaciones 6:29 TaoTao Tips: Turn Signal Mod - Duración: 5:02. They will break anyway .
I don't have the "ON/OFF" headlight switch if that's what you mean, we don't get ON/OFF headlight switches in US. Fuel flow in a basic moped is very simple. Stator and r/r have more and different color wires. Scooter Brake Light Not Working My scooter is 2002 Piaggio NRG MC-3.
Battery doesnt get charged if you dont messure over 13 volts DC mate. To the head light bulb. WTFp0s 111.780 visualizaciones 2:36 Motorcycle LED Turn Signal Flasher Relay Blink Rate Fix - Honda 919 - Duración: 8:50. http://drivit.net/not-working/chinese-scooter-lights-not-working.html Keep the shiney side up rob63 PM rob63 rob63's Posts rob63's Threads Scooter Doc Currently Offline Posts: 272 Likes: 1 Joined: May 5, 2012 14:05:15 GMT -6 Running Lights not workin
Back to step 1 Step 7 Spark plug cap and wire If you have come this far and your moped still isn't running then it's time to replace the spark plug Have you swapped the headlight bulb just to make sure the low beam filament isn`t busted ? Also check the soldering and terminals on the connections to the regulator make sure they are making good connections. Using the multimeter, set to D.C.
Acción en curso... The carburetor does this with very small diaphragms, orifices and ports, which are easily clogged by contaminants. I assume these are the same types of bulbs. If you aren't getting anything from this feed then there is probably something amiss with the stator.
Now go back to step 1 to see if this did the trick. same with blinkers since they require a min voltage to blink or work... If you have a diagram in your manual it may help. Did you...
I'm stopping for the night having run out of light and patients.